|
4400 Mobile Phone Tester Series |
Caractéristiques (en anglais) |
| General data |
| Control interfaces |
IEEE 488.2 (GPIB) |
| LAN (RJ-45, TCP/IP) |
| USB type A, USB type B |
| PS/2 keyboard |
| VGA |
| PS/2 mouse |
| RS-232 (access through RAPID!) |
| Main power supply |
94 to 132 VAC |
| 187 to 264 VAC |
| H x W x L |
180 x 360 x 330 mm |
| Weight |
10.5 kg (without options) |
System functions
GSM System Option
| Supported GSM frequency bands |
| GSM 850 (channel 128 to 251) |
| R-GSM, E-GSM, P-GSM (ch. 955 to 974, 975 to 1023, 0, 1 to 124) |
| GSM 1800 (channel 512 to 885) |
| GSM 1900 (channel 512 to 810) |
| Transmitter measurements |
| Phase- and frequency error measurement |
Timing advance |
| Power measurements |
Modulation spectrum |
| Power/time template |
Adjacent Channel Power Meter (ACPM/ORFS) due to modulation and due to switching transients |
| GSM Call Processing |
| Location update |
SMS to mobile (idle mode) |
| Mobile-originated call |
SMS to mobile (on TCH/FS) |
| Mobile-terminated call |
SMS from mobile (idle mode) |
| Intracell handover |
Special functions |
| Cross-band intracell handover |
Call state diagram |
| Call clearing by MS |
Paging test |
| Call clearing by 4400 |
Reduced signalling |
| Open loop, closed loop procedures |
MS information display |
| Early or late assignment |
|
| Receiver measurements |
| Bit Error Rate (BER) |
Fast Bit Error Rate (FBER, C loop) |
| Residual Bit Error Rate (RBER) |
Frame Erasure Rate (FER) |
GPRS Option
| Supported GPRS frequency bands |
| GSM 850 (channel 128 to 251) |
| R-GSM, E-GSM, P-GSM (ch. 955 to 974, 975 to 1023, 0, 1 to 124) |
| GSM 1800 (channel 512 to 885) |
| GSM 1900 (channel 512 to 810) |
| Transmitter measurements |
| Supported number of time slots transmitter measurements: 1 through 4 |
Timing advance |
| Phase- and frequency error measurement |
Modulation spectrum |
| Power measurements |
Adjacent Channel Power Meter (ACPM/ORFS) due to modulation and due to switching transients |
| Power/time template |
|
| Signaling procedures |
| GPRS attach/detach |
Reduced signalling |
| Routing area update |
Uplink data modes according to GSM 04.14 Modes (a) |
| downlink TBF establishment |
Uplink power control method closed loop |
| Uplink TBF establishment (using ETSI-defined GPRS test mode command) |
|
| Receiver measurements |
| Displayed results are minimum, maximum, average BLER/BER |
BLER-BCS measurement |
| Coding scheme CS-1 |
BLER-USF measurement |
| Data PRBS (PN-9, PN-15, PN-23) |
|
EDGE Option
| Supported EDGE frequency bands |
| GSM 850 (channels 128 to 251) |
| P-GSM (channels 1 to 124) |
| E-GSM (channels 975 to 1023, 0 to 124) |
| R-GSM (channel 955 to 1023, 0 to 124) |
| GSM 1800 (channels 512 to 885) |
| GSM 1900 (channels 512 to 810) |
| Transmitter measurements |
| Frequency Error |
Origin Offset |
| RMS EVM |
I/Q Imbalance |
| Peak EVM |
Displayed results for selectable time slot, results via SCPI for 1 selectable of for all time slots |
| 95th Percentile |
|
| Receiver measurements |
| BLER-BCS (CS-1) |
BLER-USF (up to 4 time slots) |
| Signaling procedures |
| EDGE attach/detach |
ETSI Test Mode A only |
| Uplink TBF establishment |
|
CDMA2000 Option
| Supported CDMA2000 frequency bands |
| Band 0 – US Cellular (channel 1 to 1023) |
| Band 1 – PCS Band (channel 1 to 1199) |
| Band 2 – TACS Band (ch. 1 to 1000, 1329 – 2047) |
| Band 3 – JTACS Band (ch. 1 to 799, 801 to 1039,1041 to 1199, 1201 to 1600) |
| Band 4 – Korean PCS (channel 1 to 599) |
| Band 5 – NMT-450 (ch. 1 to 300, 1039 to 1473,1792 to 2016) |
| Band 6 – IMT-2000 (channel 1 to 1199) |
| Band 8 – 1800 MHz (channel 1 to 1499) |
| Band 9 – 900 MHz (channel 1 to 699) |
| Transmitter measurements |
| Power measurements |
| Minimum/maximum RF power |
Access probe power |
| Open loop power (level and timing) |
Closed loop power (min./max. only) |
| Gated output power |
Standby power |
| Modulation quality measurements |
| rho |
Code domain power (graphical and data) |
| Frequency error |
Code channel time offset |
| rms vector error |
Code channel phase |
| Time offset |
Adjacent channel power |
| Amplitude imbalance |
Modulation spectrum analyzer |
| Signaling procedures |
| Mobile-originated call |
Call clearing by MS |
| Mobile-terminated call |
Call clearing by 4400 |
| Intracell handover |
Special functions call state diagram |
| Cross-band handover |
|
| Receiver measurements |
| Receiver performance sensitivity |
Demodulation of forward traffic with AWGN |
| Dynamic range (Frame Error Rate) |
Mobile reported FER, pilot strength |
| Demodulator performance |
|
WCDMA Options
|
|
|
|
| Supported WCDMA bands |
|
Band I
|
1920 – 1980 MHz (uplink)
|
2110 – 2170 MHz (downlink)
|
| Band II |
1850 – 1910 MHz (uplink) |
1930 – 1990 MHz (downlink) |
| Band III |
1710 – 1785 MHz (uplink) |
1805 – 1880 MHz (downlink) |
| Band IV |
1710 – 1755 MHz (uplink) |
2110 – 2155 MHz (downlink) |
| Band V |
824 – 849 MHz (uplink) |
869 – 894 MHz (downlink) |
| Band VI |
830 – 840 (uplink) |
875 – 885 (downlink) |
| Band VIII |
880 – 915 (uplink) |
925 – 960 (downlink) |
| Band IX |
1749.9 – 1784.9 (uplink) |
1844.9 - 1879.9 (downlink) |
| Band X |
1710 – 1770 (uplink) |
2110 – 2170 (downlink) |
| Transmitter and receiver measurements |
| Maximum/minimum output power |
Adjacent Channel Leakage Ratio (ACLR) |
| Frequency error |
Spectrum Emission Mask (SEM) |
| Output power dynamics in the uplink |
Transmit modulation (EVM and PCDE) |
| Modulation spectrum |
Reference sensitivity level and maximum input level |
| Occupied Bandwidth (OBW) |
Constellation display |
| Signaling procedures |
| URA procedure (location updating) |
Call setup procedures (both voice call and RMC) |
HSDPA Options
| Supported HSDPA bands |
|
Same as for WCDMA options
|
| Transmitter and receiver measurements |
| Power measurements |
Maximum input level for HS-PDSCH reception (16QAM) |
| Frequency error |
CQI reporting |
| Peak and rms EVM |
Maximum throughput test |
Peak code domain error PCDE
Spectrum Emission Mask (SEM) |
Adjacent Channel Leakage Power Ratio (ACLR) |
| Signaling procedures |
URA procedure (location updating)
CS Attach and PS Attach |
Call setup procedures (using RMC) for different DL signal configurations |
TD-SCDMA Options
| Supported frequency bands |
| 800 to 1000 MHz |
1700 to 2300 MHz |
| Transmitter and receiver measurements |
| Channel power |
Peak power |
| Mean power |
Min and max power |
| Inner loop power control |
Open loop power control |
| Transmit ON/OFF time mask |
Error vector magnitude |
| Frequency error |
Waveform quality (rho) |
| Magnitude and phase error |
Rho |
| I/Q offset, I/Q imbalance |
Constellation display |
| Modulation spectrum |
Adjacent channel leakage power ratio (ALCR) |
| Occupied bandwidth (OBW) |
Spectrum emission mask (SEM) |
| Peak code domain error (PCDE) |
Code spectrum |
| BER/BLER measurements |
UE Info with UE Measurement Report |
| Signalling procedures (4451 TD-SCDMA Call Mode Option) |
| Registration |
Mobile originated call |
| Mobile terminated call |
Call clearing by mobile and tester |
| Inter-frequency handover (channel change) |
RMC 12.2 kbit/s (single code, multicode)
RMC 64 kbit/s |
1xEV-DO Options
| Supported 1xEV-DO frequency bands |
| Band 0 – US Cellular (channel 1 to 1023) |
| Band 1 – PCS Band (channel 1 to 1199) |
| Band 2 – TACS Band (ch. 1 to 1000, 1329 – 2047) |
| Band 3 – JTACS Band (ch. 1 to 799, 801 to 1039,1041 to 1199, 1201 to 1600) |
| Band 4 – Korean PCS (channel 1 to 599) |
| Band 5 – NMT-450 (ch. 1 to 300, 1039 to 1473,1792 to 2016) |
| Band 6 – IMT-2000 (channel 1 to 1199) |
| Band 8 – 1800 MHz (channel 1 to 1499) |
| Band 9 – 900 MHz (channel 1 to 699) |
| Transmitter and receiver measurements |
| Power measurements |
Modulation quality measurements |
| Rho |
Frequency error |
| RMS vector error |
Time offset |
| Amplitude imbalance |
Code domain power |
| Modulation spectrum |
Receiver sensitivity (call mode option) |
| Receiver dynamic range (call mode option) |
|
| Signaling procedures |
| Protocol Revision 0 and A |
Test Application (FTAT, FETAP, RTAP, RETAP) |
| AT Session Open |
AT & AN Data Connection |
| AT & AN Session Close |
AT & AN Connection Release |
| Handover |
|
RAPID! Application Programming Environment
| RAPID! = Run Application Programs with Integrated Development environment. |
| RAPID! a programming language (a modern structured BASIC dialect) |
| RAPID! a programming environment |
| Input/output control from RAPID! programs |
| GPIB |
Floppy and hard disk access |
| RS-232 |
Screen (text-based) |
| parallel port (printer) |
Keyboard, incl. barcode reader support |
| Other programming features |
| Direct access to SCPI command set, to control the 4403/4405 and collect measurement results for postprocessing information hiding (program files can be protected against reading by the user) |
| Functions of built-in programming environment |
| File manager |
Debug screen |
| Editor (multiple files) |
Display of variables contents |
| Runtime I/O screen |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
16 février 2011
Le nouveau micrologiciel pour le 2305 Stabilock ajoute la fonction Autorun au test des stations de base, une nouvelle option pour la commande à distance des stations de base
> plus
|
|
|
|
|
2 février 2011
Aeroflex lance de nouvelles options pour le 2201 ProLock Phone Tester en vue d’augmenter la vitesse des tests WCDMA, d’ajouter la fonction Handover vers GSM ainsi que le test HSDPA
> plus
|
|
|
|
|
20 avril 2010
Un nouveau testeur TETRA pour les stations de base et les terminaux radio
> plus
|
|
|
|
|
|
|
|
|
4916 Antenna Coupler - Nouvelle Génération de Coupleur d'Antenne pour tous les téléphones mobiles
> plus
|
|
|
|
|
|
 |
|
 |
|
 |
|
 |
|
|
